What Size Hole To Drill For 1/4 20 Tap
what size drill bit for 1/4 20 tap?
02-12-2004, 12:01 AM
Member
Thread Starter
My Feedback: (one)
Bring together Date: Jan 2004
Location: portland, OR
Posts: 81
Likes: 0
Received 0 Likes on 0 Posts
what size drill fleck for 1/four xx tap?
I am taping holes for my wing bolts, I have the 1/iv twenty bolts and tap but tin can't call up what size drill bit I need to use.
If its one/4" I'm going to experience stupid.
Thank you.
02-12-2004, 12:25 AM
My Feedback: (eleven)
Join Date: January 2002
Location: Missoula, MT
Posts: 9,060
RE: what size drill scrap for 1/4 twenty tap?
Use a number 7 drill flake. If you lot don't have i, you will take to pick one up at the hardware shop.
02-12-2004, 12:46 AM
My Feedback: (14)
Join Date: Dec 2001
Location: St. Louis, MO
Posts: v,057
Likes: 0
Received 1 Like on ane Mail service
RE: what size drill fleck for one/four 20 tap?
Pigsty tapping requires odd size bits. This numbered bits are sized by wire gauge. Here is a link that shows a Craftsman set. You tin purchase them individually if the whole fix is non needed.
http://world wide web.sears.com/sr/javasr/produ...id=00906819000
Eric
02-12-2004, 01:19 AM
Senior Member
Join Date: Nov 2002
Location: Rochester, MN
Posts: one,270
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill bit for 1/iv 20 tap?
A #vii drill scrap.
02-12-2004, 01:44 AM
Senior Member
My Feedback: (2)
Join Date: Mar 2002
Location: Sugar State, TX
Posts: 439
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill bit for i/four twenty tap?
themanimal
This might be handy to you the next time you need to drill and tap a pigsty.
Accept fun flight
Lee
02-12-2004, 09:10 AM
Senior Fellow member
Bring together Date: Jan 2003
Location: Spring Hill, FL
Posts: 4,734
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill scrap for 1/four twenty tap?
a three/16" bit is close plenty if yous're borer wood.
02-12-2004, x:34 AM
My Feedback: (40)
Bring together Engagement: Dec 2001
Location: Waynetown, IN
Posts: 2,476
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill fleck for i/four twenty tap?
OR if you are tapping wood, and you lot are going to become purchase a bit, Apply A NUMBER eight INSTEAD OF 7....I accept found that going down 1 size when tapping wood works VERY WELL....A #vii gives you the proper contact percentage for metal.
02-12-2004, 01:05 PM
Senior Member
My Feedback: (4)
Join Date: April 2002
Location: Willmar, MN
Posts: 28,519
Likes: 0
RE: what size drill fleck for i/4 20 tap?
Cafeen'south right, if information technology'south forest a 3/16 will work. A thirteen/64 is amend yet. (information technology's merely 2 thousanths of an inch larger than a #7 -- That's about the thickness of a human hair) (No, not a Ruby-red pilus)
02-12-2004, 04:sixteen PM
Banned
Join Date: Jan 2003
Location: gone,
Posts: 4,923
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill bit for i/4 20 tap?
you'd be suprized how minor a drill volition work if tapping woods. You can get abroad with a one/8 inch drill for a i/4-20 tap in a pinch. Its a bit harder to tap out the hole... you take to back out and clear the chips a lot.
In one case, I actually drilled and tapped in one stride. It worked simply it was very irksome.
A good tap and die ready will list different airplane pilot drill sizes for different materials to get the best threads. When you lot are cutting threads in soft metal (contumely and similar), part of the metallic bulges in toward centre, so you don't want quite as large a hole diameter as when doing steel or cast iron.
02-12-2004, 07:14 PM
Senior Member
Join Appointment: Nov 2002
Location: Crete, IL
Posts: 2,251
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill bit for 1/4 20 tap?
Near quality taps have the recommended drill size stamped correct on them.
02-12-2004, 08:43 PM
Member
Thread Starter
My Feedback: (1)
Join Engagement: January 2004
Location: portland, OR
Posts: 81
Likes: 0
Received 0 Likes on 0 Posts
RE: what size drill bit for one/4 20 tap?
ok ok. Who would take thunk that everyone would be soo interested in taps and drill sizes.
I used the 3/16 and information technology worked like a charm. At that place are many times where I tell myself, its a model airplane, not the space shuttle so merely make it work and salvage yourself some time and coin.
Thanks again,
brian
02-13-2004, 12:58 AM
Senior Fellow member
My Feedback: (ix)
Join Date: Dec 2003
Location: haverhill, MA
Posts: 1,511
Likes: 0
Received one Like on 1 Mail
RE: what size drill bit for 1/4 20 tap?
ORIGINAL: themanimal
In that location are many times where I tell myself, its a model plane, non the space shuttle so only make information technology piece of work and save yourself some fourth dimension and money.
Yeah but why non spend the time and practise it right, then having to spend time again fixing what wasnt correct the kickoff time?
Posting Rules
You lot may not post new threads
You may not mail replies
You may non postal service attachments
You lot may non edit your posts
HTML lawmaking is Off
What Size Hole To Drill For 1/4 20 Tap,
Source: https://www.rcuniverse.com/forum/questions-answers-154/1520107-what-size-drill-bit-1-4-20-tap.html
Posted by: dillopith1974.blogspot.com
0 Response to "What Size Hole To Drill For 1/4 20 Tap"
Post a Comment